|
![](https://ae01.alicdn.com/kf/Hed75f073a24e449d8a7288a9b344e4abd/Kakute-F7-v1-5-AIO-BetaFlight-PX4-ArduPilot.jpg) aHR0cDovL2ZyZWVzaGlwLmNvLmty![](https://ae01.alicdn.com/kf/Hed75f073a24e449d8a7288a9b344e4abd/Kakute-F7-v1-5-AIO-BetaFlight-PX4-ArduPilot.jpg) ![](https://ae01.alicdn.com/kf/Hfc27403242374029afeec8564239e886J/Kakute-F7-v1-5-AIO-BetaFlight-PX4-ArduPilot.jpg)
- ºê·£µå À̸§: Fly thinking Dili Asia
- ±Ù¿ø: CN (Á¤Ç°)
¿É¼ÇÁ¤º¸[(771)Kakute F7 v1.5] [(100012350)Kakute F7 v1.5 AIO]![](https://ae01.alicdn.com/kf/Hed75f073a24e449d8a7288a9b344e4abd/Kakute-F7-v1-5-AIO-BetaFlight-PX4-ArduPilot.jpg_640x640.jpg) The Holybro Kakute F7 flight controller makes it easy to build your multirotor. It integrates flight controller (FC) and on-screen display (OSD) in one. The Kakute F7¡¯s layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy. IMU updated to MPU6000,Re-designed and more reliable damping structure
Features - Supports Betaflight.
- Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
- Soft-mounting built in. The IMU (¡°gyro¡±) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
- High-performance / low-noise / high sensitivity IMU. MPU6000 with 6-axis gyro and accelerometer.
- Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
- Dedicated bootloader button for easy firmware flashing.
- Low-profile design fits into even very compact frames.
- Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on ¡°B+¡± pad only).
- Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.
- Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
- Supports BLHeli pass-through for easy ESC upgrade and configuration.
Specifications
- MCU: STM32F745 32-bit processor
- IMU: MPU6000 (SPI)
- Barometer: BMP280
- Current Sensor: Approximately 130 amps maximum measurable value
- USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
- 6 hardware UARTS (UART1,2,3,4,6,7)
- All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without ¡°uninvert hack¡±.
- Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
- TF card for Blackbox logging
- Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
- Mounting Holes: Standard 30.5mm square to center of holes
- Weight: 8g
![](https://ae01.alicdn.com/kf/H1ea5f55d1b4e4e32a7e03313aa8451053.jpg) ![](https://ae01.alicdn.com/kf/H1ea5f55d1b4e4e32a7e03313aa8451053.jpg) ![](https://ae01.alicdn.com/kf/Ha112ef6b95254a13bf75f89881ebaa32f.png)
Package Includes: FC board *1 Foam*1 JST SH 8pin 150mm cable*1
�:
PX4 ͳËìäÌ??Ù¥:
PX4 ͳËìÌãËìïÒ?ÙþËì:
Ardupilot ͳËìäÌ??Ù¥ÐàÌãËìïÒ?ÙþËì:
|
|
|
|
|