KAMTP 4W Solar Panel Power 5V/12V Built-in 2PCS Rechargeable Battery Supply For Wireless Security Camera Outdoor Video Surveillance Solar Power
Charging precautions(NOTE)
1. For the first use, be sure to leave the panel without any equipment connected to it and charge it in the sun for more than 2 days.
2. Press the switch and the red light is on, indicating that the battery voltage is above 2.8V and placed in the sun. The green light is on to indicate that it is charging, and the green light is off to indicate that it is fully charged.
3.If the battery voltage is lower than 2.8V, in order not to affect the battery life, recharge, the panel will stop outputting voltage. Please restart the solar panel after charging.
Instructions for powering the camera
Please make sure whether your camera is a low-power camera, the one that can sleep is low-power, and the continuous working time that can`t sleep is short, about 8-10 hours.
Purchase options£º
5V DC1.35mm£º5V DC1.35mm Output Solar Panel without Battey
5V DC1.35mm BY£º5V DC1.35mm Output Solar Panel with 2PCS Battey
5V USB £º5V USB Output Solar Panel without Battey
5V USB BY £º5V USB Output Solar Panel with 2PCS Battey
12V DC2.1mm£º12V DC2.1mm Output Solar Panel without Battey
12V DC2.1mm£º12V DC2.1mm Output Solar Panel with 2PCS Battey
1.Green Solar Energy & Built-in 6000mAh Battery:
Renewable and abundant solar power, environmental-friendly, you don¡¯t need to change the battery frequently and pay for the electricity anymore, saving time and money. Built-in 6000mAh battery could also offer power to battery IP camera/hunting camera even if no sunshine outside.
2.360 Degree Adjustable Wall Mount:
Easy to install and ensure to get maximum solar power. It comes with a 13ft/ 2m long DC 5V cable for more convenient mounting.
3.Weather Resistant Design:
IP66 Waterproof, dustproof and cold resistant. Weather-resistant materials making it perfect for outdoor use.
Parameter introduction
This is a 4W solar panel with battery, 5V voltage output, maximum current up to 1A.
Battery selection
Up to 6 18650 batteries can be installed
You can install more batteries by yourself
PCBA definition interface
Please refer to the figure below for the definition of PCBA wiring.
1.USB_POWER+: connect with external USB power supply 5V+
2.GND:GND
3.BAT+£ºBAT+: battery voltage output, (3.8v), when POWER KEY is pressed, BAT+ voltage is 3.8V, when POWER KEY is pressed again, BAT+ voltage is 0V.
4.BAT-£ºBAT-: The negative pole of the battery, the voltage is 0V when working.
5.Solar_VCC+:The output voltage of the solar panel, (0-7V), when the sun is sufficient, will generate a maximum voltage of 7V, which is input to the charging board.
6.PTZ_EN£ºThe signal input pin for boosting output 5V. When the input is high, the charging board outputs a stable 5V2.4A power supply. When the input is low, the charging board stops outputting 5V power.
7.solar_out_vcc:5V power output interface
8.solar_vcc:Solar panel input interface, power supply (0-7V)
Switch button introduction
Solar panel has indicator function
Switch button
Waterproof grade IP66
DC specification is 1.35mm
If you need special customization, please contact us.
The battery camera matched with this solar panel.
If you need a battery camera, please click connect to buy.
FAQ£º
1. The solar panels on the market have a warranty of only 3 months, but the solar panels break down after a few months and cannot be recharged. Buyer feedback is not durable.
The problem of circuit design. The general situation is that when the sun`s rays are sufficient, the problem of excessively high power generation voltage of the cell is relatively high. Our solar panels choose original factory charging chips, with a withstand voltage of at least 7V.
2. Many solar panels on the market have no way to know the state of charge of the internal battery, no power switch, no indicator light?
Our solar panels have switches. A red indicator light indicates that the battery has voltage output, a green light on indicates that it is charging, and a green light off indicates that it is fully charged.
3. Buyers who purchase solar panels report that the output voltage is inconsistent with the description, and the PCB does not have a boost converter?
We use IC boost, continuous output power, there is no such problem.
4. The solar panel can`t keep working in the dark, need better built-in battery?
The boost efficiency must be above 92%, and the boost efficiency is too much without using IC, most of the energy is converted into heat, which shows that the battery is not durable.
5. The solar panel battery does not respond to charging?
Our solar panels have indicator lights to indicate that they are charging.
6. Is the solar glass panel easy to break?
Our solar panels are wrapped with pearl cotton during transportation. Can reduce the occurrence of this situation.
7. The solar panel plastic base installation lock device has poor texture and feels cheap?
Our bracket is a private model design, it doesn¡¯t seem to be too LOW
8. There is no explanation about the buttons or functions of the product?
Our solar panels have instructions for use.