aHR0cDovL2ZyZWVzaGlwLmNvLmty
- ¸ÂÃã °¡´É À¯¹«: ±×·¸½À´Ï´Ù
- ¸ðµ¨ ¹øÈ£: SK-190
- ±Ù¿ø: CN (Á¤Ç°)
- Color: Black
- Origion: Mainland China
- Certificate: CE
- Compatibility: C-C
- Frequency: 1.8/1.9Ghz DECT
¿É¼ÇÁ¤º¸
[(193)SK-190 Belt Pack]
TELIKOU¢ç??Intercom System
SKYLINE SK-100 / SK-190 Wireless Intercom
Instruction Manual
¨Ï TELIKOU Systems
All Rights Reserved
I. INTRODUCTION
Thank you for choosing TELIKOU?SKYLINE series wireless?intercom products.
Our website:
SK-100 is a 4+2 channels full-duplex intercom system that integrates 4 wireless channels?and 2 wired channels.
SKYLINE wireless intercom system?is suitable for television station, communication center, UB truck, live performance and any other environment which requires wireless communication.
SKYLINE system adopts DECT technology. It has the characteristics of flexible configuration, simple operation, stable and reliable performance, strong anti-noise, clear and loud voice quality, etc.
II. Features
1.?4 wireless channels support max 16pcs wireless belt pack packs.
2.?Internal 2-wire/4-wire interface
3.?Announcement output and AUX audio input.
4.?Mobile power supply port for antenna
5.?Relay control interface
6.?Wireless belt pack can roam between different antennas.
7.?4 channel wireless Tally
8.?Belt Pack supports ISO function
9.?Out of signal range alarm
10.?IFB earphone connector ( Optional with Tally light connector)
11.?USB charge port for SK-190 belt pack
12.?Long standby and working time
13.?Supports 4xAA rechargeable and ordinary battery
14.?Battery level indicator and low battery alarm
III. Main Station
Main station is the control unit for the whole wireless system. It talks with the corresponding group of any antenna?through the button switch on front panel. ?It also can sent program audio, 2-Wire and 4-Wire audio to the system. When the active antenna is less than 400 meters away from the base station, the power is supplied by the base station;?otherwise, the power is supplied by the local 24V or the USB port 5V.
Front Panel
1.?Headset
XLR-5M Pin definition£º
Pin 1?-- Mic-
Pin 2?-- Mic+
Pin 3?-- Ear-
Pin 4?-- Ear+
Pin 5?--?Ground
2.?Panel Gooseneck Microphone
4 Pin Aviation Pin definition£º
Pin 1?-- Mic-
Pin 2?-- Mic+
Pin 3?-- Ground
Pin 4?-- Null
3.?Volume / Menu Control knob
Rotary encoder with switch. The rotary encoder is used to adjust the volume of the base station
headphones, with a total of 16 choices. When the switch is pressed for more than 3S, the base
station enters the setting function.
4.?MIC Button
Press this button will turn on the microphone.
5.?Channel Button (TALK) and Indicator LED
Each?button corresponds?one antenna group. For example, press channel 1 button to talk with belt packs which under antenna #1.?In standby mode, if press MIC button on belt pack, the LED above corresponding channel button?will flash. Press channel button to enter full duplex model.
???If more than one channel button is pressed, these groups make a big communication group.
6.?LCD screen
l?LCD screen display content under working status
First Line :The name of antenna
Second Line :The number of registered belt packs?and?the status of Aux In.
???????????????If antenna is not connected, this line is blank.
Note: if ¡°Wrong Insertion¡± is displayed here, it means SK-100ANT antenna is connected with wrong port.
Hold Volume/Menu knob more than 3s, LCD screen?enters?setting menu. By rotating the Volume/Menu knob, the cursor will move between options, and the cursor will stop at a certain option, press the knob once to enter the option. Rotate the knob clockwise and anticlockwise to select the value of this option and return to the previous menu. In the top menu, select ¡°Save&Exit¡±?or ¡°Exit¡±?to exit the setting menu.
l?The Settings
Language :?English or Chinese
MIC Select :Headset - When select this, panel microphone and panel speaker do not work.
Panel MIC - When select this, headset microphone does not work. Headset
earphonevolume drops 6dB.
MIC Gain :?If most external devices hear the SK-100¡¯s voice too loud or too small,adjust
panel microphone gain. It has 16 levels.
Local Side Tone :?Adjust the audio level which SK-100 hears its own voice. It has 16 levels.?
Side Tone Null :?Adjust the side tone of 2-wire channel.
AUX. Audio :To select which channel receives auxiliary audio?to four?wireless and two wiredchannels.
On ?: Aux audio in is enable
OFF : Aux audio in is disable
Tally :?Screen shows Tally 1 - Tally 4 four tally?signals. Choose any signal, screen
shows belt pack 1 to belt pack 16. Then assign the selected tally signal to
any?belt pack.
Save&Exit :?Save change and exit setting
Exit :?Without save any change and exit setting
7.?AUX. In
Allows auxiliary audio?input?to system. The green LED above lights constantly.
8.?AUX In Level Adjustment
Adjusts the auxiliary?audio level input.
9.?4-Wire
Allows external 4-wire device connected to system. The green LED above lights constantly
10.?4-Wire Level Adjustment
Adjust the 4-wire audio level input
11.?2-Wire
Allows external 2-wire device connected?to base station. The green LED above lights constantly
When receives call signal, the green LED above flashes.
12.?ANN. Out
????Press and hold the button to sent microphone signal to ANN.out connector. The LED above lights. The?internal relay pull in. The relay connector at rear panel status changes. Release the button, relay returns to its original state.
13.?Panel Speaker
When microphone is selected as panel microphone. Panel speaker works.
Rear Panel
1.?Power Connector
AC 90V~260V, 50-60Hz
2.?DB-9 Data Connector
This DB-9F?connectorreceives four?dual color tally signals and they can be?assigned to any?four
beltpacks.The 3.5mm jack on SK-190T belt pack connects TL-2 tally light.
Low voltage lights on. High voltage lights off.
Pin definition:
Pin 1 --- Tally 1 Green
Pin 2 --- Tally 1 Red
Pin 3 --- Tally 2 Green
Pin 4 --- Tally 2 Red
Pin 5 --- Tally 3 Green
Pin 6 --- Tally 3 Red
Pin 7 --- Tally 4 Green
Pin 8 --- Tally 4 Red
3.?Relay Connector
6.35mm / 1/4 inch connector. When ANN.Out button is pressed, this relay is closed.
???Contract rating: 250V/3A AC, 30V/3A DC.
???Note: Please be cautious when connecting AC high-voltage equipment to the port !
R: Normally Closed Contact
T: Moving Contact
S: Normally Open Contact
4.?ANN. Out
???Base station microphone output.
Output level : 1Vp-p
???XLR-3M connector:
?Pin 1 --- GND
Pin 2 --- Audio Out?+
Pin 3 --- Audio Out -
5.?4-Wire Connector
??RJ-45 Connector:
Pin 1 --- GND
Pin 2?--- 12VDC
Pin 3?--- Audio Out +
Pin 4 --- Audio In +
Pin 5 --- Audio In -
Pin 6?--- Audio Out -
Pin 7?--- Control Signal
Pin 8 --- GND
6.?2-Wire Connector
???XLR-3M Connector
Pin 1 --- GND
Pin 2?--- 24VDC / 0.5A
Pin 3?--- Audio
7.?AUX. In
???XLR-3F Connector, 1Vp-p audio level
Pin 1 --- GND
Pin 2?--- Audio In +
Pin 3?--- Audio In -
8.?Transceiver Connector
???Four RJ-45 connector to Antenna, Shielded twisted pair cable.
???RJ-45 Connector:
Pin 1 --- GND
Pin 2?--- 24VDC
Pin 3?--- Tx +
Pin 4 --- Rx +
Pin 5 --- Rx -
Pin 6?--- Tx -
Pin 7?--- 24VDC
Pin 8 --- GND
These four ports are marked with 1,2,3,4. They are corresponding with #1,#2,#3 and #4 SK-100ANT antennas. When you connect with SK-100ANT antenna, please make sure proper sequence antenna is connected with proper port.
IV?Active Antenna
The signal coverage radius of the antenna in the open area is 300 meters. Each antenna?can
connect?up to 4 wireless belt packs.
1.?Power Connector
Pin 1 --- GND
Pin 2 --- Null
Pin 3 --- Null
Pin 4 --- 12~24VDC
2.?USB Connector
External power bank supplies 5VDC
3.?Antenna Sequence Number
???Two digits coding switch. Please follow the chart which printed about the switch to set the proper antenna sequence. The number at the top of the chart is the antenna number
corresponding to different dial positions.
Note: If antenna is connected with wrong port which is at rear panel of SK-100, the SK-100
LCD screen will display ¡°Wrong Insertion¡±.
4.?Register
???????Belt pack should register?with all antennas that belt pack may roam to.
A)?Pairing Belt Pack
???Press and hold theregister button more than 3s until?the?indicator flash. Belt pack enters setting menu and selects registration. Once the indicator becomes solid, it means that the pairing process is completed. Antenna backs to normal working mode. ??
B)?Delete Belt Pack
???Make?sure all the belt packs which are paired with this antenna is turned on. Press and hold the register button until?the?indicator flash. Press register button 7 times will delete all the belt pack pairing.
??????Note: If belt pack is not turned on before antenna deletes belt pack pairing. This belt pack
must pairing again with same antenna otherwise this belt pack can not work properly.
Or this belt pack must be reset and paired again before use.
5.?Power?and Registration Indicator
After power on, the indicator light is always on. When the antenna enters theregistration
state, the indicator flashes slow (1s). After pairing finished, the indicator light becomes
always on.
6.?Active Antenna Connector
??RJ-45 connector. Antenna connects to base station through shielded twisted pair?CAT5 cable.
Pin 1 --- GND
Pin 2?--- 24VDC
Pin 3?--- Rx +
Pin 4 --- Tx +
Pin 5 --- Tx -
Pin 6?--- Rx -
Pin 7?--- 24VDC
Pin 8 --- GND
Please connect this port with proper SK-100 transceiver connector.?The sequence numbers
should correspond one to one.
7.?SMA Antenna Connector
???Two SMA connectors
V. Belt Pack
SKYLINE-190 belt pack uses 4x AA battery. Ni-MH & Ni-Cd Rechargeable battery can be charged through micro-USB connector. Inthe multi-antenna signal coverage area, belt pack can manually switch to different registered antenna.?When walk over the antenna coverage, belt pack headset gives warning sound.
Belt pack is in standby mode after power on. When there is an external call, it will answer automatically. When press Mic button, it will make a full duplex communication.
Note: Li-on batteries and ordinary?batteries are can NOT?be charged by SK-190 belt pack.
1.?Power Button?and Volume Adjustment
With switch encoder. Turn it clockwise or anti-clockwise to adjust earphone audio volume. There
Is 16 levels to select. If hold button more than 5s, the belt pack is turned on or off.
2.?Mic Button
???Touch button
???Press to latch or release the headset microphone.
3.?3.5mm Connector
1.?Tally light connector with SK-190T belt pack. ?
2.?3.5mm earphone connector with SK-190E belt pack.
R £ºEarphone +
T £ºEarphone -
S £ºGND
4.?Micro-USB Connector
Charging port. If belt pack is using Ni-MH/Ni-Cd rechargeable batteries, these batteries can
be charged directly through a 5VDC adapter.
Note: Li-on batteries and ordinary?batteries are can NOT?be charged.
5.?Headset Connector
???XLR-5M connector
Pin 1 --- Mic -
Pin 2?--- Mic +
Pin 3?--- Ear -
Pin 4 --- Ear +
Pin 5 --- GND
6.?ISO Button
???Press and hold the button. The belt pack makes an isolated conversation with ISO target belt pack. Release the button, the ISO conversation is finished.
???ISO target should be the belt pack which under same antenna or main station.
7.?LCD Screen
l?Display content:
n?Registered antenna number, Current working antenna number?and?Signal field strength
n?Battery Power
n?Working Frequency
n?Belt Pack Label (BP-1, BP-2, BP-3, BP-4,BP-5, BP-6,...,BP-16 )
n?ISO Target Label ( ISO: Null, BP-1, BP-2, BP-3, BP-4,BP-5, BP-6,...,BP-16)
n?Tally?Status (at the right side of belt pack label).
If belt pack activates tally function, it shows Tally N (N=1-4). If not, it shows blank.
l?Setting Menu
???Hold the power button and press MIC button will enter setting menu. LCD screen displays menu. Rotate the power and volume encoder to move?the cursor. When the cursor is on an
???option, press the power and volume encoder to enter the option. Rotate the power and volume encoder to Change parameters.
n?Language: English or Chinese
n?ISO Set: Base and other belt packs which under same antenna
n?Mic Gain: Level 1 ~ Level 16
n?Frequency: select 1.8G or 1.9G, then select country or area. If any belt pack changes frequency, all the other belt packs under same antenna change as well.
n?Registration: Register belt pack?to antenna
This item is only displayed when SK-190 belt pack is not registered or not connected with any antenna.
n?Label: BP-1, BP-2, BP-3, BP-4,BP-5, BP-6,...,BP-16
n?Reset: When the belt pack can not work normally due to problems such as registration, you can use this function to clear the registration information and restore the factory settings.
n?Save&Exit: Save change and exit
n?Exit: Exit without save any change
8.?Roaming
???Every belt pack can be paired with four antennas. Belt pack shows the antenna number?(1-4)
whichare already paired on LCD screen. Belt pack can roam among these antennas. Press and
rotate the power and volume encoder can switch antenna manually.
9.?Change Frequency
SK-100 system is default with 1.9G. If system?need to be changed to other?frequency. Please?followthe following steps.
1.?Power on the system. Make sure SK-100 main station and every SK-100ANT antennas and SK-190 belt packs are well connected and powered on.
2.?Take any SK-190 belt pack which working with #1 SK-100ANT antenna at the moment.
3.?Enter menu -> Frequency. Select exactly frequency and country or area.
4.?Save and Exit.
#1 SK-100ANT antenna and rest belt packs which are connecting with #1 SK-100ANT switches to new frequency.
5.?Repeat for #2,#3 and #4 SK-100ANT antenna.
Please Note:
This process is only need to be done once with SK-190 belt pack for any SK-100ANT.
If any SK-190 belt pack is not powered on when changing frequency. It will connect failed with antenna when it is on. This belt pack can be set frequency separately.
VI Cable
The cable between SK-100 base station and SK-100ANT antennas should be T568A or T568B shield CAT-5 cables. When SK-100ANT antennas are powered by SK-100 base station, this cable should no longer than 200m. If SK-100ANT antenna is powered locally, this cable is no longer than 800m.
VII Technical Parameters
1.?Power:
SK-100 main station : AC 90V~260V, 50-60Hz
SK-100ANT : 12~24VDC / 5VDC
SK-190 Belt Pack : 4xAA Battery or 4xAA Rechargeable Battery
Note: Li-on batteries and ordinary?batteries are can NOT?be charged.
Standby Time: Over 72 hours
Working Time: Over 10 hours
Charging: Micro-USB 5VDC
2.?Size
???SK-100 Base Station: 480 x 255 x 45mm
SK-100 Antenna: 135 x 130 x 50mm(without antenna), 165 x 130 x 200mm(with antenna),
SK-190 Belt Pack: 105 x 90 x 35mm
3.?Weight
???SK-100 Base Station: 2KG
SK-100 Antenna:0.45KG
SK-190 Belt Pack: 0.12KG (without battery)